Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
ActiveYards Fence Installation: The Jacksonville Owner’s Guide
ActiveYards fence installation in Jacksonville typically runs $3,500 to $9,000 installed, depending on linear footage, gate count, and whether we’re pulling old posts or setting new ones. We stock ActiveYards-compatible posts, rails, pickets, and gate hardware on our trucks, which means most repairs and full runs get quoted and started without waiting on a parts order. Most Jacksonville homeowners call us after a storm season has done its work: posts that were set shallow start leaning, gate hinges sag under their own weight, or the bottom rail has rotted clean through from sprinkler overspray against the pickets.
What separates an ActiveYards system from a generic box-store panel is the way it’s engineered for assembly: heavier-gauge aluminum, locking rail brackets, and posts that are designed to take a wind load without twisting. That also means the failure points are specific. When we walk a Jacksonville fence line, we’re not guessing at what went wrong. We’re looking at post depth, rail bracket torque, gate hinge alignment, and whether the original installer mixed ActiveYards components with aftermarket fill-ins that never quite matched.
Which ActiveYards Models This Applies To
ActiveYards produces several fence lines that show up consistently in Jacksonville backyards: the Brookhaven, Fairmont, and Hampton collections are the ones we see most often in vinyl, and the Aluminum Estate and Aluminum Deluxe lines for metal. The compatibility gotcha that trips up a lot of homeowners is this: ActiveYards rail brackets and post caps are sized to their own post dimensions, and those dimensions shift between product grades. A Fairmont post cap will not seat properly on a Hampton post, even though both are 4×4 nominal. Same story with gate hinges: the self-closing hinge assembly for the Aluminum Estate line uses a different bracket pattern than the Deluxe line, and forcing the wrong hinge strips the post threads and voids any remaining manufacturer warranty.
If you’re trying to identify which line you have before we arrive, look for the embossed rail stamp on a picket or rail end. ActiveYards stamps most of their vinyl profiles with a product code near the bottom of the picket or on the underside of the top rail. If you can’t find a stamp, measure the picket wall thickness: ActiveYards vinyl pickets generally run between .080 and .120 inches thick depending on the collection, where most aftermarket box-store pickets come in around .060. That thickness difference is what lets a Brookhaven panel take a Northeast Florida thunderstorm without buckling.
On the OEM versus aftermarket question: for posts and gates, we install OEM ActiveYards whenever the line is still in production. The post wall thickness and UV stabilizers are matched to the rail system, which matters in Jacksonville’s sun. For fill-in pickets and top rails on older runs where ActiveYards has changed profile, we’ll use a gauge-equivalent aftermarket profile that matches the original dimensions and color, and we’ll tell you before we do it. Color match on older vinyl is not exact; the original fence has sun-aged, and new material will never be a perfect match the day it goes in. It evens out over 12 to 18 months.
Styles & brands we work with
Signs Your ActiveYards Fence Installation Is Failing
- Posts leaning or pulling out of the ground. This is the number one failure we see across Jacksonville, and it almost always comes down to post depth. A properly set ActiveYards post sits 30 to 36 inches below grade with concrete around the full embedment. When installers trench only 18 to 24 inches to save time, the first big storm pushes the fence over.
- Gates sagging and scraping the ground. ActiveYards gate frames are built to handle a specific panel weight, and the self-closing hinges have an adjustment range. When a gate drags, either the hinge bracket has loosened in the post, or someone hung a heavier gate panel on a hinge set rated for a lighter one. In Riverside and Ortega, where lots are flat and gates swing over concrete walkways, we see this constantly.
- Bottom rails separating from pickets. Sprinkler heads placed too close to the fence line soak the bottom rail. Vinyl expands and contracts with temperature, and a repeatedly soaked bottom rail will work itself out of the bottom channel, leaving pickets hanging by a single top rail. We recommend a minimum of 12 inches between a sprinkler head and the fence line.
- Pickets cracking or splitting along the top edge. In vinyl, this is usually UV degradation after years of direct exposure without a cap or rail to shade the top edge. In an aluminum system, cracking at the picket-to-rail connection is usually a sign of a bent rail or an improper bracket install that put tension where there shouldn’t be any.
- Wind noise or visible panel flex during storms. ActiveYards panels are designed to flex in high wind, but not permanently deflect. If you can push a fence panel with one hand and see the posts move, the structure is compromised. In Jacksonville’s coastal wind zones, a fence that flexes at the posts becomes a projectile risk in a named storm.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For a full ActiveYards fence installation in the Jacksonville market, you’re looking at $3,500 to $9,000, and the number is driven almost entirely by linear footage and gate count. A standard 100-foot run with one gate on flat ground sits at the bottom of that range. A 200-foot run with two gates, old concrete post footings to remove, and a property line that follows a slope lands at the top. If the job is a partial repair rather than a full run, most rail, picket, and bracket replacements land between $400 and $1,800, and we’ll write the scope so you know exactly what’s being replaced before we cut anything loose.
Every ActiveYards fence installation we quote includes removal and haul-off of the old fence, new post footings set to the depth specified for Jacksonville’s soil and wind conditions, the ActiveYards or gauge-equivalent components specified in the quote, gate hardware with proper hinge and latch adjustment, and a site walk at close. You get a written price before any work starts, and the price doesn’t move unless you change the scope. The whole job is covered by the 365-Day Done Right Promise: if the fence or gate fails in its first year, we return and correct it at no charge.
DIY or Call Us?
Some things are worth checking yourself. You can confirm which ActiveYards line you have by checking the rail stamp or measuring picket thickness. You can note where the fence leans and which gates drag. You can verify post depth on a failed post by digging down alongside it, though we’d rather do that ourselves with the right shoring so the post doesn’t come down on you. What you shouldn’t do is pull a 40-pound ActiveYards panel off its rails to “just see what’s loose.” Those locking brackets hold under tension, and when they release, the panel drops hard. Same with gate springs: ActiveYards self-closing hinges are under load, and removing the wrong bolt will snap the hinge arm back with enough force to break a finger.
We’d rather have you call us before you’re in the middle of it. We answer the phone, we come look, and we give you a written number for the repair or the full replacement. If it’s a simple call, we’ll tell you that on the phone. If it’s structural, the free estimate is the fastest way to know what you’re actually dealing with. Call (904) 337-5929.
FAQs
How long does an ActiveYards fence last in Jacksonville? In Jacksonville’s heat, humidity, and storm exposure, a properly installed ActiveYards vinyl fence runs 20 to 30 years with occasional cleaning, and aluminum runs 30-plus. The posts are the limiting factor: set them shallow and the fence is on borrowed time from day one.
Can you repair my ActiveYards fence instead of replacing it? Yes, in most cases we can replace individual posts, rails, pickets, or gate hardware as long as the remaining components are structurally sound and the post spacing hasn’t drifted. We’ll tell you honestly if a repair is throwing money at a frame that’s already compromised.
How long does a full ActiveYards fence replacement take in Jacksonville? A standard 100- to 150-foot run with one gate takes one to two days on site, plus a day for concrete to cure before gates are hung and adjusted. Larger runs or jobs with old concrete removal can run three to four days, and we’ll put that timeline in writing.
Do you stock ActiveYards parts or do I need to order them myself? We stock common ActiveYards profiles, brackets, post caps, and gate hardware on our service trucks, and we source OEM or gauge-equivalent material for specific lines as needed. You don’t need to source anything yourself; if you already bought parts, we’ll install them after verifying they’re the correct spec for your fence, but we can’t warranty parts we didn’t supply.
Written by Curtis Lane, Owner, Bradford Remodeling Co Jacksonville at Bradford Remodeling Co Jacksonville, serving Jacksonville and nearby areas.
