Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CGI Kitchen Remodeling: The Jacksonville Owner’s Guide
If you own a home in Jacksonville with a CGI kitchen remodel already underway or an existing setup that’s starting to show its age, you’re in the right place. Bradform Remodeling Co Jacksonville installs and services CGI-compatible kitchen remodeling projects throughout Jacksonville, with most full kitchen remodels running between $14,000 and $45,000 depending on cabinet line, countertop material, and the condition of what’s underneath. We stock CGI-compatible components on our trucks and can typically diagnose what failed during the first visit. Most Jacksonville homeowners discover a problem the same way: a cabinet face pulls loose from its hinge, a drawer slide binds mid-pull, or a countertop seam opens up after a humid stretch and never closes again.
What we do differently is simple. Before any tool comes out, you get a written price for the entire job. If the work doesn’t hold, our 365-Day Done Right Promise has us back on site at no charge. That’s the Garrison Standard we’ve run on since 2004, and it’s how Curtis Lane runs the Jacksonville crews.
Key Takeaways
- CGI kitchen remodeling in Jacksonville typically runs $14,000 – $45,000 installed, with smaller scopes starting around $9,000.
- We stock CGI-compatible components and can identify most failures during the first site visit.
- Every project gets a written price before work starts, and a full-year written guarantee when it’s done.
- Bradford Remodeling Co Jacksonville is an independent service provider, not affiliated with CGI.
Which CGI Models This Applies To
CGI isn’t a cabinet brand. It’s a specification standard used in certain production-built and semi-custom homes across Florida, and the “CGI” label usually shows up on the interior trim package, the cabinet door profile, or the hardware set that shipped with the original builder package. In Jacksonville, we see it most often in communities built between 2005 and 2018, where the builder offered a CGI upgrade package for the kitchen. The giveaway is usually a small CGI stamp on the back of a drawer box or the inside of a cabinet door hinge.
Here’s what actually matters: the cabinet box construction, the door hinge spread, and the drawer slide length. Most CGI-spec boxes we pull in Jacksonville are 5/8-inch particleboard with a vinyl-wrapped or painted MDF door. That’s not a knock, it’s just the spec. The hardware spread is usually 48mm full-overlay, but we’ve seen 35mm in a handful of Riverside and Ortega properties. We confirm before ordering anything.
When it comes to OEM versus aftermarket, the honest answer is this: for cabinet boxes and doors, OEM makes sense when you’re matching a discontinued color or a specific door profile. For hinges, drawer slides, and soft-close dampeners, quality aftermarket equivalents from the same manufacturers CGI’s suppliers used perform just as well and cost less. We’ll tell you which is which, in writing, before you spend a dollar.
Styles & brands we work with
Signs Your CGI Kitchen Remodeling Is Failing
- Hinges that sag or bind within months of adjustment. This usually means the hinge plate has stripped out of the particleboard substrate behind it. Turning the screw tighter just makes the hole wider. The fix is a new hinge with a larger screw pattern or a structural repair behind the plate.
- Drawer slides that catch halfway or drop on one side. In Florida humidity, the grease in original-equipment slides breaks down faster than it does elsewhere. Once the bearing race wears, no amount of cleaning brings it back. We swap the slide pair, not just the failing side, or you’ll be back here in six months.
- Delaminating cabinet door corners, especially near the dishwasher or sink base. Moisture gets under the edge band and the MDF core swells. Once it’s swollen, the door is done. Touching it up with paint won’t fix the core.
- Countertop seams that open and close with the seasons. Jacksonville’s wet summers and dry winters move slabs more than you’d think. A seam that visibly flexes is a sign the installer didn’t use enough adhesive or the supporting cabinet below has settled. Either way, it won’t fix itself.
- Soft-close dampeners that slam or oil-stain the cabinet interior. The little hydraulic piston inside the hinge has blown its seal. It’s a five-minute swap per hinge, and we keep these on the truck.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Full kitchen remodeling in Jacksonville runs $14,000 to $45,000. Smaller refreshes where we keep the existing footprint, replace doors and hardware, and resurface counters land between $9,000 and $20,000. Here’s the line-item breakdown we give every homeowner before work starts:
- Cabinet installation: $4,000 – $13,000
- Countertop installation: $2,000 – $6,500
- Backsplash installation: $800 – $2,500
- Kitchen island installation: $3,000 – $10,000
Every line is written down with the exact materials specified. If we’re installing KraftMaid or Wellborn cabinetry, the spec sheet says so. Cambria or Silestone counters? Same deal. You’ll know what you’re paying for before we touch a tool, and the number won’t change at the door. Our work is covered by the 365-Day Done Right Promise: if anything we installed fails within the year, we come back and fix it. No invoice, no argument.
DIY or Call Us?
Some things you can check safely. Pull the drawers out, look for the manufacturer stamp, and measure your hinge spread with a caliper. That’s all useful information when you call us. But replacing cabinet hinges on a particleboard box is where DIY goes sideways. Overtighten one screw and you’ve stripped the substrate, which turns a $40 repair into a box rebuild. Same with countertop seams. If the joint is moving, slapping caulk over it just locks moisture behind the seam and accelerates the problem. Scope it right the first time, the job goes a lot smoother when nobody’s surprised. Call (904) 337-5929 and we’ll tell you what you’re actually looking at.
FAQs
With proper substrate prep and name-brand hardware, a full kitchen remodel in Jacksonville should hold for 15 to 25 years before major components need replacement. Cabinet boxes in Florida’s humidity typically outlast the hardware, so expect hinge and slide replacements around year 8 to 12 even on a good install.
Yes, in most cases hinge plates, drawer slides, and soft-close dampeners are serviceable parts, and we repair them without tearing out the boxes. If the particleboard behind a hinge has crumbled or the door core has swollen from water, replacement of that specific component is the honest fix.
A full CGI kitchen remodel in Jacksonville takes two to five weeks from demo to final walkthrough, depending on counter template lead time and whether we’re moving plumbing or electrical. Smaller hardware and cabinet repairs are usually done in one visit.
We keep common hinge spreads, drawer slides, and dampeners on the truck, so most hardware failures get fixed the day we show up. For matched cabinet doors or full box replacements, we order from our documented supplier list, including KraftMaid and Wellborn, and provide a written timeline before we place the order.
If your CGI kitchen in Jacksonville is starting to show any of these symptoms, call (904) 337-5929 for a free estimate. Curtis Lane and the Bradford Remodeling Co Jacksonville crew will give you a straight answer, a written price, and a job that’s actually squared away when we leave.
Written by Curtis Lane, Owner, Bradford Remodeling Co Jacksonville at Bradford Remodeling Co Jacksonville, serving Jacksonville and nearby areas.
