Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
PGT Fence Installation: The Jacksonville Owner’s Guide
PGT fence installation in Jacksonville typically runs $3,500 to $9,000 for a complete perimeter install, including materials, concrete footers, and labor. Most single-gate repairs or panel replacements land between $400 and $1,600. We stock a full range of PGT-compatible hardware on our trucks and can usually swap a failed gate or panel same-day once we confirm your measurements.
Most Jacksonville homeowners discover the problem the hard way: a gate that drags across the paver driveway, a panel that bows after a summer squall, or a latch that quit catching entirely. PGT builds a solid vinyl and aluminum fence line, but salt air, sandy soil, and afternoon thunderstorms don’t do the hardware any favors. The good news is that the failure is usually isolated to one component, not the whole system.
Which PGT Models This Applies To
PGT’s residential fence line breaks down into three main product families: the PGT VinylGuard series (routed vinyl panels with aluminum reinforcement inserts), the PGT AluminumGuard series (powder-coated aluminum pickets and rails), and the PGT CoastalGuard line, which is rated for high-wind zones and common here along the beaches and intracoastal from Atlantic Beach down to Ponte Vedra. Each series uses different post dimensions, rail brackets, and gate hinge plates, so swapping parts across series doesn’t work without modification.
To identify what you have, check the post cap or the inside face of the top rail for a stamped or embossed model number. If that’s weathered off, measure the post: VinylGuard posts run 5×5 inches, AluminumGuard typically 2.5×2.5 or 4×4 depending on height, and CoastalGuard uses 4×4 reinforced posts with crush-resistant internals. For OEM versus aftermarket on PGT specifically, we recommend OEM for anything load-bearing: gates, hinge posts, and corner posts. Aftermarket aluminum brackets and rail clips from a known manufacturer are fine for light-duty panel work, but the spec differences on CoastalGuard wind-rated hardware are too tight to risk a knockoff. Bradford Remodeling Co Jacksonville is an independent service provider and not affiliated with PGT; we install and service their product lines because they hold up in this climate, not because anyone asked us to say so.
Styles & brands we work with
Signs Your PGT Fence Installation Is Failing
- Gate drag or sag with a visible gap at the top hinge. The hinge post has shifted off plumb, usually because the original footer was poured shallow. In sandy Jacksonville soil, a 24-inch footer is the minimum for a 6-foot gate post; anything less and the post walks over two or three seasons.
- Panel rattle or movement when the wind picks up. The rail brackets have loosened or corroded. Coastal salt air eats zinc-plated hardware in a few years; PGT’s stainless bracket sets are the only fix that lasts east of the St. Johns River.
- White chalky residue on vinyl panels at the rail connections. That’s the aluminum reinforcement oxidizing inside the routed channel. It means the internal insert was cut too short when installed, and water is pooling inside the rail. Left alone, the channel will crack at the corners.
- Latch mechanism catches but won’t hold. The striker plate has slipped or the gate frame has racked out of square. Adjusting only the striker without squaring the gate means it fails again in a month.
- Bottom rail bowing upward between posts. Drainage holes are clogged and the rail holds water. During a hard freeze, that water expands and pops the rail apart at the bracket.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For a full Jacksonville PGT fence installation, budget $3,500 to $9,000 depending on linear footage, gate count, and whether you’re on sandy fill or clay. The low end covers a straight 100-foot vinyl run with one walk gate on level ground. The high end reflects 200-plus feet with double drive gates, CoastalGuard wind-rated hardware, and concrete removal if you’re replacing an old wood fence. We write every quote with the material line items separated from labor so you can see exactly where the money goes.
What’s included: measured and ordered materials, old fence removal and disposal if applicable, concrete footers poured to depth, post set and cured before panels hang, hardware torqued to spec, gate alignment and striker adjustment, and a clean haul-away of all packaging and scrap. The work carries the 365-Day Done Right Promise in writing. If the gate sags, the panel fails, or the latch stops holding inside that year, Curtis Lane’s crew returns and corrects it at no charge. That’s the Garrison Standard, and it’s on the paper you sign before we start.
DIY or Call Us?
You can check the obvious stuff yourself: confirm the model stamp, measure your post spacing, check whether the gate post rocks when you push it top and bottom. If the post moves at the base, the footer is gone and no amount of hinge adjustment will save it. Re-setting a gate post in sand without the right geotextile and concrete depth is where most Jacksonville DIY jobs go wrong, and that’s before you get to stringing a 200-foot panel line square.
For anything involving the gate assembly, the hinge posts, or CoastalGuard wind-rated hardware, we’d rather you didn’t test your luck. A 6-foot gate panel carries real weight; when a post lets go, it’s not a dent, it’s a broken leg or a dented car. Scope it right the first time, the job goes a lot smoother when nobody’s surprised. If you’d rather not, call (904) 337-5929 and we’ll bring the right parts the first trip.
FAQs
A properly installed PGT fence in Jacksonville lasts 20 to 30 years for the vinyl and aluminum structure, with hardware replacement typically needed at the 8-to-12-year mark due to salt air corrosion. Call (904) 337-5929 if your fence is hitting that window and the gates are getting loose. We’ll inspect and price the fix.
Yes, if the failure is isolated to a bracket, hinge plate, or internal aluminum reinforcement, we can repair it without pulling the panel. If the vinyl channel has cracked at the corner or the post has shifted in the footer, replacement is the honest and cheaper fix over time. Call (904) 337-5929 and we’ll tell you which situation you’re in after a 20-minute site check.
A typical 100-to-150-foot vinyl fence with one or two gates takes two to three days on site: day one for demo and post footers, day two for post cure and rail hang, day three for gates, hardware, and cleanup. CoastalGuard installs with wind-rated strapping run a day longer. When you call (904) 337-5929, we’ll give you a written schedule with the quote instead of a vague “sometime next month.”
We stock common PGT VinylGuard and AluminumGuard hardware on our trucks: stainless hinge sets, striker plates, rail brackets, post caps, and gate frame inserts. Oddball CoastalGuard components are ordered direct and typically arrive in three to five business days. Call (904) 337-5929 with your model stamp and we’ll confirm what’s on hand before we come out.
If your PGT fence is failing, don’t wait for the gate to drop on the driveway. Call (904) 337-5929 for a free estimate. Curtis Lane and the Bradford Remodeling crew will scope it, price it in writing, and stand behind the work for a full year. We also keep parts for KraftMaid, Cambria, and Silestone if you’ve got other projects stacking up.
Written by Curtis Lane, Owner, Bradford Remodeling Co Jacksonville at Bradford Remodeling Co Jacksonville, serving Jacksonville and nearby areas.
